Machine Components

The J.W.Winco series EN630 design of ledge handles matches the product family of the Ergostyle. A typical application for ledge handles is on double swing doors on machine shrouds or fixtures. The ledge handles are protection for the operator’s fingers. At the same time they shroud the two fixing screws of the ledge handle.

• Counterbored Through Holes
• Hole Distance: 93.5 mm
• Finish: Black

The J.W.Winco series EN630 design of ledge handles matches the product family of the Ergostyle. A typical application for ledge handles is on double swing doors on machine shrouds or fixtures. The ledge handles are protection for the operator’s fingers. At the same time they shroud the two fixing screws of the ledge handle.

• Counterbored Through Holes
• Hole Distance: 93.5 mm
• Finish: Black

The J.W.Winco series EN630 design of ledge handles matches the product family of the Ergostyle. A typical application for ledge handles is on double swing doors on machine shrouds or fixtures. The ledge handles are protection for the operator’s fingers. At the same time they shroud the two fixing screws of the ledge handle.

• Counterbored Through Holes
• Hole Distance: 93.5 mm
• Finish: Black

The J.W.Winco series EN630.1 is an original design technopolymer plastic Ergostyle off-set open "U" Handles. When using guards on machines and automation systems, which include double hinged doors, use of colored caps makes identification of handle easier. Resistant to solvents, oils, grease and other chemical agents.

• Counterbored Through Holes
• Hole Distance: 93.5 mm
• Finish: Black

The J.W.Winco series EN630.1 is an original design technopolymer plastic Ergostyle off-set open "U" Handles. When using guards on machines and automation systems, which include double hinged doors, use of colored caps makes identification of handle easier. Resistant to solvents, oils, grease and other chemical agents.

• Counterbored Through Holes
• Hole Distance: 93.5 mm
• Finish: Black

The J.W.Winco series MFE has good ergonomic features. The MFE series is the economical version of the MF series. Maximum heat resistance is 150 °F.

• Counterbored Mounting Holes
• Hole Distance: 93.5 mm
• Finish: Black Matte

The J.W.Winco series MFE has good ergonomic features. The MFE series is the economical version of the MF series. Maximum heat resistance is 150 °F.

• Counterbored Mounting Holes
• Hole Distance: 117 mm
• Finish: Black Matte

The J.W.Winco series MFE has good ergonomic features. The MFE series is the economical version of the MF series. Maximum heat resistance is 150 °F.

• Counterbored Mounting Holes
• Hole Distance: 117 mm
• Finish: Black Matte

The J.W.Winco series MFE has good ergonomic features. The MFE series is the economical version of the MF series. Maximum heat resistance is 150 °F.

• Counterbored Mounting Holes
• Hole Distance: 132 mm
• Finish: Black Matte

The J.W.Winco series MFE has good ergonomic features. The MFE series is the economical version of the MF series. Maximum heat resistance is 150 °F.

• Counterbored Mounting Holes
• Hole Distance: 132 mm
• Finish: Black Matte

The J.W.Winco series MFE has good ergonomic features. The MFE series is the economical version of the MF series. Maximum heat resistance is 150 °F.

• Counterbored Mounting Holes
• Hole Distance: 179 mm
• Finish: Black Matte

The J.W.Winco series GN426.5 can be mounted from the back (Type A) or from the operator's side (Type B). In the latter case, the stud is first screwed in from the machine side and then the handle is pushed on and secured with the grub screw. The mounting studs allow the handles to be assembled back to back, to produce a double handle.

• Tapped Holes
• Hole Distance: 300 mm
• Finish: Shot-Blasted
• Thread: M10